Escort Shotgun Will Not Feed Shells

• Common Problems
  • Loose Or Rusted Chokes (Blown Barrels)
  • Not Cycling
  • Misfiring
  • Jamming Problem
  • Stovepipe
• How To Maintain And Clean The Hatsan Escort
• Conclusion

The Hatsan Escort shotgun is a firearm that generates a lot of mixed reactions among users.

But what this shotgun is being bashed for is also present in other firearm products.

It is inevitable for any firearm to be problem-free, whether it is a mechanical or cartridge malfunction problem.

So, you might wonder what the Hatsan Escort shotgun problems are and how you can solve them?

These questions, solutions, tips, and other necessary information will be discussed in this article.

So, read on to understand the Hatsan Escort shotgun's problems and their solutions.

Common Problems

Encountering a problem with your shotgun can be very frustrating, especially when it catches you unaware.

It becomes necessary to know how to deal with these issues, and below are the common problems Hatsan Escort users face.

Loose Or Rusted Chokes (Blown Barrels)

The choke of a gun is a slight constriction built close to the muzzle inside the barrel. The size of the constriction is so tiny that its measurement is in the thousandth inch.

In older versions of a shotgun, the choke was designed to be fixed, but it has been reversed in modern shotguns, allowing it to be cleaned and greased.

And because of this modern change, the choke is susceptible to loosening, which impacts the barrel of your gun. It might blow the barrel or cause some problems.

Also, if you allow moisture to get into the barrel of your gun, it can lead to rusting of the chokes.

The rust will make it nearly impossible to change the chokes without boring the barrel.

It could affect you when you want to increase the range of your shot or sell your shotgun to someone else.

Solution

1. Always keep your gun dry after use.
2. Carry out a regular maintenance routine to ensure that your gun is in good condition.
3. If it is rusted, visit your local gunsmith to help you fix it.
4. If it is loose, tighten the screw to ensure firm.

Not Cycling

Cycling is the time it takes your gun to go through feeding, chambering, locking, firing, unlocking, extracting, ejecting, and cooking after a shot has been fired.

In other words, it is the time interval between two shots. When your Hatsan Escort fails to fire, the lifter has failed to drop down to the feed position.

Instead, it drags on one side of the receiver, stopping the shell from clearing out the magazine tube.

A simple tap on the lifter can force the round out of the magazine tube to complete the feed cycle.

Aside from the lifter, a buffer can also cause a cycling problem. When wear and tear sets in, it can affect the buffer spring, which can halt the chambering process.

Solution

1. You can clean and grease the buffer spring to element frictional problems.
2. You can visit your local gunsmith to fix the cycling problem.
3. You can temporarily tap the lifter to fix the problem, but if it does not work, then seek professional help.

Misfiring

The misfiring problem does not affect only the Hatsan Escort gun; it is a common problem for all shotguns.

This problem occurs when the priming mixture is not initiated after the firing pin strikes the primer. This problem can also be referred to as failure to fire.

The light firing pin hit is the most common cause of misfiring in the Hatsan Escort shotgun.

And you can identify it by the shallow indentation on the primer cup after removing the cartridge from the chamber.

This problem can be more complicated because it can be mistaken for a hangfire. A hangfire is a similar problem that ends up firing after some time.

It is dangerous because if you assume a misfire, then if the gun points at someone or something, it can cause severe damage.

So, it is always safe to assume that every misfire is a hangfire to protect yourself and others.

Solution

1. You can fix this problem by servicing the gun, and you can do that by disassembling it and greasing the parts.
2. Visit your local gunsmith to get it fixed.

Note: In the case of a failure to fire or misfire, point the muzzle of your gun to a safe area and wait for a few minutes. After which, you can disassemble it and fix it.

Jamming Problem

It is one of the most prevailing problems of the Hatsan Escort shotgun because the shooter primarily causes it.

The causes could be improper shooting technique or loading, failure to maintain the firearm by cleaning and lubricating it, and faulty or incompatible ammunition.

Also, it can be caused mechanically by faulty or worn-out springs, damaged parts, break-in periods, and parting shots.

So, any of the above or a combination of the above can cause the jamming in your Hatsan Escort shotgun.

Solution

1. Learn proper shooting techniques.
2. Buy compatible ammunitions.
3. Change worn-out springs.
4. Regular and thorough maintenance should be done, like cleaning and lubricating the parts.

Stovepipe

The stovepipe problem occurs in a Hatsan Escort shotgun when a used shell is not ejected fast or far enough to go out of the bolt.

When this occurs, you will see the shell sticking out of the shotgun, preventing the Hatsan Escort from completing its cycle.

It can be caused by bad magazines, a dirty gun, poor ammunition, or a bad recoil spring.

Solution

1. To resolve this problem in your Hatsan Escort, rack the bolt while rolling the gun on its side. When you do this, the shell will fall off from the bolt.
2. For a more permanent fix, visit your local gunsmith.
3. Carry out thorough maintenance on the firearm.

Tip: You can create the scenarios artificially and try to fix them yourself. So, you will be prepared when the time comes and help others get solutions.

How To Maintain And Clean The Hatsan Escort

To clean the Hatsan Escort thoroughly, you will have to disassemble it. And this should be a regular practice after each use.

Materials needed: cleaning rod, brass bore brush, cotton bore patches, powder solvent, good quality shotgun oil, and a small soft brush.

Steps:

• Use the bore brush and the cleaning solvent to clean the barrel and chamber.
• Clean the bolt using a soft brush and lubricate it with the oil.
• Clean the outside of the magazine tube and the trigger assembly.
• After a thorough clean-up, oil every part and wipe with a cloth.
• Assemble the parts and try the firearm to see if it's in good condition.

Tip: Always ensure that the muzzle is pointed in a safe direction before you try to fix your firearm and your finger is removed from the trigger.

Conclusion

The Hatsan Escort firearm is an excellent shotgun with its fair share of challenges like other firearms.

And these solutions can help you be prepared to deal with any of the common problems highlighted in this article.

dotsonsuallible.blogspot.com

Source: https://homesteadandprepper.com/hatsan-escort-shotgun-problems/

Share this post